News

How Does the Manufacturer Pack the Viking Ship Ride?

2026-10-12 08:38:15

How Does the Manufacturer Pack the Viking Ship Ride?

A viking ship ride is one of the largest machines a park can buy, and the way it leaves the factory matters almost as much as the way it swings. The hull, the A-frame, the pendulum arms and the drive all have to travel by road and sea without losing their alignment, their paint or their bearings. This article follows a Viking Ship Ride Packing and Shipping job from the pre-assembly bay to the container door, and explains what a buyer should expect to see on the packing list, in the crates and on the documents before the ship ever arrives on site.

01

Why Packing Decides How The Ride Arrives

A viking ship ride is not a single welded machine that can simply be lifted onto a truck. The finished ride is a pendulum ship suspended between two steel towers, driven by a large axle assembly with a motor, reducer and either a crank linkage or a rubber tyre drive. To fit legal transport limits and to keep freight costs reasonable, the machine is built and test assembled in the workshop, then taken apart into major assemblies for shipment.

That split is decided by engineering, not by convenience. Every part is numbered to match the general arrangement drawings and the foundation plan, so the site team can identify a beam, a bearing block or a section of the ship before they open the second crate. When this numbering and the packing list are done properly, a two week installation becomes a two day one; when they are not, crews waste days matching loose plates by eye.

Viking ship ride hull and frame prepared for packing at the factory

The order of packing also follows the order of assembly. Parts that are needed first on site are loaded last, so they come out of the container first, and the heaviest steel is placed at the bottom of the load rather than on top of finished cabin parts.

02

Breaking The Ship Down Into Shippable Assemblies

The hull is the biggest question in the pack. Large ships are usually built in sections with bolted flanges, so the cabin is split into two or three pieces that can be handled by a forklift and re-bolted on site, with the joint supported by an internal rib that stays with the hull. Smaller ships can travel complete, but even then the decorative bow, the dragon head or the carved side panels are removed and packed separately to protect them in transit.

The A-frame towers are shipped as single fabricated columns whenever their length allows, with the base plates protected by wooden battens and the machined bearing seats covered by steel caps. If the towers are too tall for a standard container, they are split at a bolted splice that is marked with the assembly number and match drilled at the factory. The pendulum arms, the cross beams and the axle housing follow the same rule: match drilling at the works, painting at the works, and a stencilled number on every joint.

The drive package travels as its own unit. The motor and gearbox are bolted to their base, the exposed shaft ends are greased and wrapped, and the rubber driving tyres, the brake unit and the small consumables are boxed instead of left loose. Seats, safety bars, lamps, and the electrical cabinet are all packed separately so that nothing sharp is lying against a painted surface for eight weeks at sea.

03

Protecting Steel, Paint And Moving Parts

Sea air reaches inside a container, so surface protection is treated as part of the build. Steel members are cleaned and finished with a primer and a topcoat before packing, and any area where the paint could be rubbed by a strap or a chain is given a temporary shield of rubber or closed cell foam. Machined surfaces, bearing journals and gear teeth are coated with heavy grease, and every bearing arrives already sealed, greased and protected by a plastic sleeve.

Protective wrapping and steel strapping on amusement ride parts

Small parts get the most attention because they are the easiest to lose. Bolts, nuts, washers, split pins, anchor templates and the sensor brackets for the drive and the height limit are counted, bagged, labelled by assembly and placed in a wooden case together with a spare parts set. Each crate carries a packing list on the outside, and the same list is emailed to the buyer before dispatch so the site team can check quantities on arrival instead of discovering a missing sensor during the first start up.

Fiberglass and foam parts such as the ship’s figurehead, hull decoration and seat backs are wrapped in bubble film, boxed with soft separators and clearly marked as fragile. Electrical cabinets travel with the doors locked, the internal terminals tightened and desiccant packs inside the enclosure to keep moisture away from the controls.

04

Amusement Ride Container Loading, Weight And Balance

Most viking ship rides are shipped in one or two 40 foot high cube containers, with an open top or flat rack used when a hull section or a long tower cannot pass the door. Loading is planned as a weight diagram before the first piece is lifted. Heavy assemblies sit low and towards the centre of the container, timber dunnage spreads the load across the floor, and steel straps or chains with edge protectors hold everything against movement during a long ocean leg.

The loading plan also protects the finished surfaces. Nothing painted or upholstered is used as a load bearing layer, stacked parts are separated by rubber mats or plywood, and the doors are closed only after the load has been photographed inside the container. Those photographs, together with the loading list, are the record that matters if a shipment is inspected or a claim has to be made later.

Buyers often ask how the ship itself is handled. The hull is lifted with certified slings through lifting points that are marked on the drawings and left in place after installation, and the towers are lifted by their own lugs at the top of the column. Handling points, sling angles and centre of gravity should all appear on the shipping drawings, because the crane capacity available at the destination port or at the park gate is not always the same as at the factory.

Viking ship ride steel frame and hull loaded for shipment

05

Documents, Spares And Tracking After Dispatch

The paperwork that travels with the ride is part of the packing job. A complete set normally includes the packing list with weights and dimensions, the bill of lading, the commercial invoice, the general arrangement and foundation drawings, the electrical schematic, the operation and maintenance manual, the material certificates for main structural steel and the inspection or load test report from the factory test run.

Amusement park viking ship ride assembled after shipping

Clear marking helps as well. Container numbers, part numbers and a simple box schedule let the park’s own team unload in the right order and store the machine under cover instead of leaving it in the rain. A short spare parts kit is worth adding to the shipment: a set of drive tyres or linkage pins, brake pads, limit switch, proximity sensor, a spare set of seat belts or restraint locks and a litre of the recommended lubricant.

From dispatch onwards, a good supplier shares the shipping schedule, sends the loading photographs and confirms the arrival date with the freight forwarder. That keeps the park’s civil contractor on schedule, since the foundation, the cable trench and the queue fencing are usually finished while the container is still at sea.

06

What To Ask A Viking Ship Ride Manufacturer About Packing

Before the order is confirmed, ask for the shipping drawings rather than only the marketing layout. Height, width and weight of each section decide the container type, the crane size at the park and the road permits on the last mile, and those numbers should be on paper before the deposit is paid.

Then ask how the machine is protected. Which surfaces get grease and which get paint? How are the hull sections joined, and is the joint match drilled so it only fits one way? Is the ship test assembled and run in the workshop, and are the test photographs provided? How are the parts labelled, and does the packing list carry weights, dimensions and the assembly number for every crate?

Finally, ask about support during installation, because a big pendulum ride is not finished when it is unloaded. A Viking Ship Ride For Sale package should normally include installation drawings, remote guidance or an on site engineer, commissioning of the drive and braking system, operator training and a set of load test records. Parks that order a Pirate Ship Ride For Sale or a viking ship from an experienced supplier usually receive the ride in numbered, protected, crated assemblies that go back together in the same order they were taken apart. That is the real test of a Viking Ship Ride Manufacturer: not the brochure photograph, but the state of the goods when the container doors are opened, and how quickly the Amusement Ride Container Loading plan turns into a running ride in the park.

Home Tel Mail Inquiry